Monthly Archives: October 2015

Sept 28 to Oct 01, 2015 – Removing Old Frames and Fitting New Ones – Part 03

Sept 28 to Oct 01, 2015 – Removing Old Frames and Fitting New Ones – Part 03

With the new frames back in my shop, I laid out where I wanted the new fastenings to be.

The old frames had one screw through the frame head and into the chine log. There was also one screw that fastened the foot of the frame to the keelson. There were just two screws that fastened the frame to the floor timber. And, there were the screws that fastened the frame to the skin of the hull. Along with these fasteners, there was also the use of resorcinol glue between the frame and the hull skin, chine log, keelson, and between the face of the frame and the face of the floor timber.

The glue joint between the floor timber and frame had failed. It had also failed between the keelson and the foot of the frame. The fastenings in these areas had also failed; rotting away.

I decided that I wanted to really “beef up” the weak areas that were present in the original design of the boat. Below is the system that I came up with.

I drilled three 3/8″ diameter holes through the face of each frame in the foot area. These holes will allow three 3/8″ diameter galvanized bolts to pass through the frame and through the floor timber. The mating surfaces of the frame and floor timber will also be glued together with epoxy.

Positioning the frames against the floor timber so that I can mark the corresponding holes of the frames on to the face of the floor timber.

With everything clamped firmly in place, I drilled a 3/8″ diameter clearance hole through the head of the frame. This will allow for a 3″ long, 3/8″diameter, galvanized lag bolt that will be much stronger than just the original countersunk screw!

In similar fashion, I will be adding two 3/8″ diameter lag bolts through the foot of each frame that will bite into the keelson.

To fasten the frame to the floor timber, I decided to make my own 3/8″ diameter bolts. The simple reason for this is; expense. By threading the ends of some 3/8″ galvanized spikes, I save 50% of what it would cost to purchase actual bolts. Besides, I really didn’t like the fact that the bolts that I had access to were threaded their entire length. I just wanted threads where I needed them to be; right at the end.

For this step, I used the actual spike to mark where the frame holes needed to be on the face of the floor timber.

I drilled the floor timber for the new frame bolts.

Back inside the boat, everything dry-fit together perfectly!

Kind of looks medieval doesn’t it!

I was able to carry the whole frame / floor timber unit out of the boat in into my shop. It was solid!

I separated the frames from the floor timber and began applying coats of System Three’s CPES (Clear Penetrating Epoxy Sealer), followed by, System Three general epoxy.

While the frames were drying, I turned my attention to the fastenings that I need to prepare for the installation of the new frames and floor timber.

Here they are.

I measured the spikes to the lengths that they needed to be cut to, and using my 4″ grinder and a metal cut-off disc, I lopped off their ends.

Using my bench grinder, I squared up the ends of the spikes and then ground a bevel so that a threading die would start easily.

I cut new threads about one inch in from the end of the spike / now bolt.

And, another coat of epoxy brushed on to the frames. Very soon, I will be able to actually put wood BACK in to the boat!

Categories: Making New Frames | 3 Comments

Sept 27, 2015 – Removing Old Frames and Fitting New Ones – Part 02

09-27-2015 – Removing Old Frames and Fitting New Frames – Part 02

With the frame outside of the boat, using various methods I removed the remaining fastenings that hadn’t broken off.

I also used my grinder to clean all of the old resorcinol glue off of the frame.

In this image, I am again pointing out the diesel fuel stains that had wicked their way up the frame from the foot. If I stick my nose against the frame towards the upper end, I can’t smell it. If I take a whiff of the foot of the frame, I can smell the fuel “loud and clear”!

Using the original frame as a “pattern”, I set my tablesaw to the same angle that needs to be cut on the new frame face that will be fitted against the skin of the hull.

I lined up the old frame with the new frame……..

……then I traced around the old frame; leaving its “footprint” on the new frame.

I cut out the new frame using my bandsaw.

Back inside the hull, I positioned the new frame where it needed to be “tuned” to be properly fitted to the hull.

Using a pair of scribes, I marked the areas of the new frame that needed to be “whittled” and ground away so that it would sit snug against the chine long, the skin of the hull, and the keelson.

And, here are the Port and Starboard frames fit!

A final detail was to rout a 1/4″ roundover on the top edges of the frame.

The next step is to fasten the matching floor timber up to these two frames. This image shows what this will roughly look like.

Categories: Making New Frames | 1 Comment

Sept 27, 2015 – Removing Old Frames and Fitting New Frames – Part 01

Sept 27, 2015 – Removing Old Frames and Fitting New Frames – Part 01

With the first batch of “frame stock” made, it was time to begin fitting the new frames into the interior of the hull. Before that could be done, I had remove the old frames.

The top portion of the lower frame is fastened by a wood screw driven through the frame head, and into the chine log. I drove a chisel into the wooden plug that covers the head of the screw and “chopped” it out of the countersunk hole it was glued into.

I did the same at the bottom of the frame where a woodscrew was driven through the frame-foot and into the keelson; revealing the head of the screw there as well.

I have been finding that, most of the steel fasteners that are located close to, or in the bilge area, are “rotten”. The fasteners have either completely rusted away, or the threads have been “eaten” and are useless. The fastener just spins in a “stripped” fashion and won’t back out of its position.

You would think that it would be easy to get these old fastenings out! But, there is also old resorcinol glue that is present from the original construction and it STILL has a grip on some of the fastenings. This is really tough stuff!

To help with removal of these screws, I heated up the tip of an old screwdriver with my propane torch…….

……..and then I placed the “red hot” tip into the slot of screw head. The heat then transferred down through the threads of the screw, helping to break the fastener free from the resorcinol glue.

Once I could wiggle the screw “back and forth” with the screwdriver, I switched over to using my brace for more leverage to back the fastener out. The screws usually broke off before completely removing them.

With the fastener removed at the frame-head and also at the frame-foot, I used a multi-tool to score the interior face of the plywood skin; creating a “break” between the glue joint of the frame and the hull surface.

Once all of the preparation work was done on the inside, I moved outside to remove the fastenings that held the plywood skin to the frames. I used the exact same procedure that I implemented to remove the floor timbers.

I chiseled a “kerf” around the top area of each screw.

Then I cut around the screw using a holesaw with the pilot bit removed from the arbor.

Back inside the hull, I gave the frame a couple of “thunks” with a rubber mallet and it popped out of its position.

Here is an image of the fastener that was holding the foot of the frame to the keelson. The threads are gone!

Here is another photograph that compares the fastener that was at the head of the frame and the one that was at the foot of the frame. As I mentioned previously, I have been finding this to be a common trait in this boat. Nearly all of the fasteners that are near, or in the bilge area, are totally shot.

Categories: Making New Frames | 2 Comments

Sept 21 – Sept 25, 2015 : Making New Frames – Part 02 (Includes A Video)

Sept 21 to Sept 25, 2015 – Making New Frames – Part 02

I continued with the system I developed of: Chopping the quartersawn Douglas Fir decking material to nominal lengths; Sanding each board to prep them for laminating with epoxy; Ripping the precut lengths in half with my tablesaw; Glueing up the “frame kits” with System Three epoxy; Then unclamping the new frames and removing the excess epoxy and prepping them for installation into the hull.

After unclamping the frames, the first step was to level the excess epoxy to bare wood using my 8″ grinder fitted with a 36 grit sanding disc.

Once the heavy glue was removed, I followed up the grinding process with my electric palm sander and 60 grit sandpaper. This step helped smooth out the frame and remove the deep scratches that the 36 grit sandpaper left behind.

Here are the frames that are nearly prepared for fitting into the hull.

And, here is a video that illustrates what the process was like to prepare the new frames for fitment into the hull.

Categories: Recent Posts | Leave a comment

Sept 14 to Sept 20, 2015: Making New Frames – Part 01

09-14 to 09-20, 2015 – Making New Lower Frame Pieces – Part 01

After I had stripped the paint from some of the frames that the new floor timbers were going to be fastened to, my suspicions and fears were realized. Just as the original floor timbers had been permanently contaminated by diesel fuel, so were the bottom sections of the frames; from the chine logs to the keelson.

In this image, you can see some dark stains towards the “foot” of the two frames where they butt into the keelson. The stains have “wicked” diesel fuel upwards from the bilge.

If this contamination is present in the forward frames, (a raised area of the bilge), then ALL of the frames aft (and lower) of here are ALSO contaminated as well! To get rid of the “fuel smell” that these timbers contain, and also to be able to have any kind of paint or epoxy to stick to them, (To seal them up and protect them.), they ALL need to be replaced! I wasn’t looking for this to happen, but it is the right thing to do.

I took some of the remaining Douglas Fir “floor timber stock” and I chopped it up into lengths that matched rough linear measurements for some of the frames that I needed to replace first.

Once cut to length, I sanded the surface of each board to prepare it for laminating with System Three epoxy.

Then, using my tablesaw, I ripped each board in half; giving me two boards of the proper width that I needed to laminate a frame with. To make a new frame, I needed six “layers” (boards) to make up the lamination.

When I had all of the pieces prepped for laminating, I arranged the lengths of wood so that the grain of each piece would oppose the grain of the wood glued next to it. When that was sorted out, I numbered each “layer”/ board to mark its location within the lamination stack.

Next, I mixed up a pot of epoxy and wet out each “mating face” of the Douglas Fir 3/4″ thick pieces of wood.

I was able to clamp up a Port and Starboard set of frames in one setup. I placed a length of waxed paper between the two laminations to be able to easily separate the two frames after the epoxy had cured.

This system seemed to be working well, so I committed to purchasing more quartersawn Douglas Fir 1″ x 4″ decking material, and I trailered it home from my local lumber yard.

I stacked the new lumber inside my garage on sawhorses.

Then, I cut most of it up into “frame lamination kits” and marked each “kit” accordingly.

I prepped each frame “kit” as I had done with my previous attempt:Chopping, Sanding, Sawing, and Glueing.

In the image below, there are 5 sets of “frame lowers”, (A set equals: One Port and One Starboard frame.), ready to be fit into the hull.

Categories: Making New Frames | Leave a comment

Sept 13, 2015 – Stripping Paint Off Of The Frames

September 13, 2015

Before I could install the new floor timbers I have been making, I needed to see what was going on with the frames that the new floor timbers would be “glued and screwed” to. To do this, I had to remove the ancient paint that had been brushed on to frame timbers way back in 1968. I tried removing the paint with a heat gun and a scraper, as well as a, conventional paint stripper too. But, I didn’t really have much luck lifting the layers of paint away from the surface of the wood.

Finally, success came in the form of a custom made tip I made from a piece of “reworked” 1/2″ copper water pipe, and slipping that over the nozzle end of a propane torch.

I donned my Full Face Respirator with fresh organic cartridges……

……and went to town “melting” and scraping paint of off the frame and chine log timbers.

Tadah! Eight hours later…….. I had a section done!

And in accomplishing this, I made a discovery that necessitated me to have to drop back and regroup my thoughts; rethinking what exactly I needed to do next with this project.

Categories: Making New Frames | Leave a comment

Sept 07 – Sept 12, 2015: More Floor Timber Work – Part 04

More Floor Timber Work – Part 04

As I was building each floor timber, I kept track of “which one was which” by marking each one on its bottom side with an ink marker. However, once tipped upright, there were no markings for me to see. It was getting confusing to know which floor timber was which, and where it’s location was to be inside the hull! (I had already made TWO of the same floor timber because I got confused as to which ones I had already made!)

I didn’t want to use an ink marker on the visible surfaces of the timber for a couple of reasons. The first reason was, I have horrible handwriting! The second reason was, I knew that the ink would “smear and run” from the solvents that were present in the epoxy solution I was going to coat the floor timbers with.

I decided to “stamp” each floor timber with markings that would ensure their proper identification.

I purchased a set of 5/16 inch “Letter & Number” stamps through Amazon.com.

Using the numbered stamps, I embossed a mark on top of each floor timber; right where a keel bolt would pass through it. These numbers matched up with the “mapping system” I had jotted down in the journal notebook entry I made for the floor timbers.

I also stamped the outboard ends of each floor timber as well. “P” stood for “Port” and “S” stood for “Starboard”. Doing this let me know which side of the floor timber was facing forward and which side was facing aft. I couldn’t “flip-flop” them by mistake with the timbers marked as such.

Once the floor timbers had been given two coats of epoxy sealer, and had been appropriately marked with their numbers and locations, I sanded down the surfaces of the timbers to prepare them for their first coat of regular epoxy.

Applying the first coat of System Three epoxy.

When the first coat of epoxy had cured, I drove the galvanized sill bolts down through the floor timbers.

They settled in quite nicely!

I added a washer and a nut, and I cinched up each fastener as tight as I could.

Using my “cutoff disc”, I removed the excess length of threads above each nut.

My next step was to flip each floor timber upside down to expose the bottom ends of the sill bolts.

I mixed up a thickened pot of epoxy, (Think of a very thick, but pourable pea soup!)…….

……..and, I filled each sill bolt hole with the glue; sealing up this area against water infiltration.

Once that epoxy had cured, I ground off the excess until the filler was flush with the surrounding surface.

Finally, I sanded down all of the surfaces one last time, and I gave each floor timber a second and final coat of System Three epoxy.

Categories: Making New Floor Timbers | Leave a comment

Blog at WordPress.com.